Kia Rio: Front Seat Belt Replacement
Front Seat Belt Replacement
•
|
When installing the belt, make sure not to damaged the
pretensioner.
|
|
1. |
Remove the following items first :
A. |
Front seat assembly
(Refer to the BD group - "Front Seat")
|
B. |
Front door scuff trim & Rear door scuff trim
(Refer to the BD group - "Interior Trim")
|
|
2. |
Disconnect the battery negative cable, and wait for at least three
minutes before beginning work.
|
3. |
The seat belt anchor pretensioner (A) can be removed after pushing
the lock pin (B) as arrow direction.
|
4. |
Using a screwdriver or remover, remove the center pillar lower
trim (A).
|
5. |
Using a screwdriver or remover, remove the center pillar upper
trim (A).
|
6. |
After loosening the mounting bolt, then remove the front seat
belt upper anchor (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
7. |
After disconnecting the pretensioner connector lock pin, remove
the seat belt pretensioner connector (A), loosen the mounting bolt,
then remove the pretensioner (B).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
8. |
Installation is the reverse of removal.
• |
Make sure the connector is plugged in properly.
|
• |
Replace any damage clips.
|
|
|
Height Adjust Replacement
1. |
Remove the following items first :
A. |
Front seat assembly
(Refer to the BD group – “Front Seat”)
|
B. |
Front door scuff trim & Rear door scuff trim
(Refer to the BD group - "Interior Trim")
|
C. |
Front seat belt lower anchor
|
D. |
Center pillar lower trim
(Refer to the BD group - "Interior Trim")
|
E. |
Center pillar upper trim
(Refer to the BD group - "Interior Trim")
|
F. |
Front seat belt upper anchor
|
|
2. |
After loosening the bolts, then remove the height adjustor (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
3. |
Installation is the reverse of removal.
• |
Replace ant damaged clips.
|
• |
Make sure the height adjust properly.
|
|
|
Front Seat Belt Buckle Replacement
1. |
Remove the following items first :
A. |
Front seat assembly
(Refer to the BD group - "Front Seat")
|
|
2. |
Remove the front seat belt buckle connector mounting clip (A).
|
3. |
After loosening the mounting bolt, then remove the front seat
belt buckle (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
4. |
Installation is the reverse of removal.
|
[Front]
(5 Door, 4 Door)
1. Front seat belt
2. Height adjust
3. Front seat belt anchor pretensioner (NA : North america)
[Rear]
...
Rear Seat Belt Replacement
[5 Door]
•
When installing the belt, make sure not ...
See also:
Inhibitor Switch Circuit Diagram
...
Tire pressure monitoring system
(1) Low tire pressure telltale / TPMS malfunction indicator
Each tire, including the spare (if provided), should be checked monthly when
cold and inflated to the inflation pressure recommended by ...
Airbag Disposal
Special tool required
Deployment tool 0957A-34100A
Before scrapping any airbags or side airbags (including those installed
in vehicle to be scrapped), the airbags or side airbag ...