Kia Rio: Front Seat Belt Replacement
Front Seat Belt Replacement
•
|
When installing the belt, make sure not to damaged the
pretensioner.
|
|
1. |
Remove the following items first :
A. |
Front seat assembly
(Refer to the BD group - "Front Seat")
|
B. |
Front door scuff trim & Rear door scuff trim
(Refer to the BD group - "Interior Trim")
|
|
2. |
Disconnect the battery negative cable, and wait for at least three
minutes before beginning work.
|
3. |
The seat belt anchor pretensioner (A) can be removed after pushing
the lock pin (B) as arrow direction.
|
4. |
Using a screwdriver or remover, remove the center pillar lower
trim (A).
|
5. |
Using a screwdriver or remover, remove the center pillar upper
trim (A).
|
6. |
After loosening the mounting bolt, then remove the front seat
belt upper anchor (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
7. |
After disconnecting the pretensioner connector lock pin, remove
the seat belt pretensioner connector (A), loosen the mounting bolt,
then remove the pretensioner (B).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
8. |
Installation is the reverse of removal.
• |
Make sure the connector is plugged in properly.
|
• |
Replace any damage clips.
|
|
|
Height Adjust Replacement
1. |
Remove the following items first :
A. |
Front seat assembly
(Refer to the BD group – “Front Seat”)
|
B. |
Front door scuff trim & Rear door scuff trim
(Refer to the BD group - "Interior Trim")
|
C. |
Front seat belt lower anchor
|
D. |
Center pillar lower trim
(Refer to the BD group - "Interior Trim")
|
E. |
Center pillar upper trim
(Refer to the BD group - "Interior Trim")
|
F. |
Front seat belt upper anchor
|
|
2. |
After loosening the bolts, then remove the height adjustor (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
3. |
Installation is the reverse of removal.
• |
Replace ant damaged clips.
|
• |
Make sure the height adjust properly.
|
|
|
Front Seat Belt Buckle Replacement
1. |
Remove the following items first :
A. |
Front seat assembly
(Refer to the BD group - "Front Seat")
|
|
2. |
Remove the front seat belt buckle connector mounting clip (A).
|
3. |
After loosening the mounting bolt, then remove the front seat
belt buckle (A).
Tightening torque :
39.2 ~ 53.9 N.m (4.0 ~ 5.5 kgf.m, 28.8 ~ 39.8 lb-ft)
|
|
4. |
Installation is the reverse of removal.
|
[Front]
(5 Door, 4 Door)
1. Front seat belt
2. Height adjust
3. Front seat belt anchor pretensioner (NA : North america)
[Rear]
...
Rear Seat Belt Replacement
[5 Door]
•
When installing the belt, make sure not ...
See also:
Starter: Components
1. Screw
2. Front housing
3. Stop ring
4. Stopper
5. Overunn clutch
6. Lever
7. Lever plate
8. Lever packing
9. Magnet switch assembly
10. Armature assemb ...
Inspection
Horn Inspection
Test the horn by connecting battery voltage to the 2 terminal and ground
the 1 terminal.
1 : 12V Ground(-)
2 : 12V (+)
...
Specifications
Item
Specifications
Transmission type
A6GF1
Engine model
Gasoline 1.6 GDI
Torque converter type
3-element, 1-stage, 2-phas ...