Kia Rio: Specifications - Automatic Transaxle System - Kia Rio UB 2012-2024 Service ManualKia Rio: Specifications

Item
Specifications
Transmission type
A6GF1
Engine model
Gasoline 1.6 GDI
Torque converter type
3-element, 1-stage, 2-phase type
Torque converter size
Ø225 mm (8.8583 in.)
Oil pump system
Parachoid
Friction elements
Clutch: 2EA
Brake: 3EA
OWC: 1EA
Planetary gear
 3EA
Gear ratio
1st
4.400
2nd
2.726
3rd
1.834
4th
1.392
5th
1.000
6th
0.774
Reverse
3.440
Final gear ratio
3.270
Fluid pressure balance piston
2EA
Accumulator
4EA
Solenoid valve
8EA (VFS:6EA, ON/OFF:2EA)
Shift lever position
 4 Range (P,R,N,D)
Oil filter
 1EA

VFS: Variable Force Solenoid
Sensors
Input Speed Sensor
▷ Type: Hall effect sensor
▷ Specifications
Operation condition (°C)°F
((-)40 ~ 150)) -40 ~ 302
Air gap(mm)in.
(1.2 ~ 1.8) 0.0472 ~ 0.0709
Output voltage(V)
High
1.18 ~ 1.68
Low
0.59 ~ 0.84

Output Speed Sensor
▷ Type: Hall effect sensor
▷ Specifications
Operation condition (°C)°F
((-)40 ~ 150)) -40 ~ 302
Air gap(mm)in.
(0.85 ~ 1.3) 0.0335 ~ 0.0512
Output voltage
High
1.18 ~ 1.68
Low
0.59 ~ 0.84

Oil Temperature Sensor
▷ Type: Negative thermal coefficient type
▷ Specifications
Temp.[(°C)°F]
Resistance (kΩ)
(-40)-40
48.1
(-20)-4.0
15.6
(0)32.0
5.88
(20)68.0
2.51
(40)104.0
1.11
(60)140.0
0.61
(80)176.0
0.32
(100)212.0
0.18
(120)248.0
0.10
(140)284.0
0.06
(150)302.0
0.05

Inhibitor Switch
▷ Type: Combination of output signals from 4 terminals
▷ Specifications
Power supply (V)
12
Output type
Combination of output signals

Solenoid Valves
Direct control VFS[26/B, T/CON]
▷ Control type : Normal low type
Control Pressure kpa (kgf/cm², psi)
9.81 ~ 500.14 (0.1 ~ 5.1, 1.42 ~ 72.54)
Current value(mA)
50 ~ 850
 Internal resistance(Ω)
5.1

Direct control VFS[UD/B, OD/C, 35R/C]
▷ Control Type : Normal high type
Control Pressure kpa (kgf/cm², psi)
500.14 ~ 9.81 (5.1 ~ 0.1, 72.54 ~ 1.42)
Current value(mA)
50 ~ 850
 Internal resistance(Ω)
5.1

Line Pressure Control VFS
▷ Control type : Normal high type
Control Pressure kpa (kgf/cm², psi)
500.14 ~ 9.81 (5.1 ~ 0.1, 72.54 ~ 1.42)
Current value(mA)
50 ~ 850
 Internal resistance(Ω)
5.1

ON/OFF Solenoid Valve(SS-A, SS-B)
▷ Control type : Normal low type
Control pressure kpa (kgf/cm², psi)
490.33(5.0, 71.12)
 Internal resistance(Ω)
10 ~ 11

Solenoid Valve Operation Table

SS-A
SS-B
UD/B-VFS
OD/C-VFS
35R/C-VFS
26/B-VFS
N/H
N/H
N/H
N/L
N, P






1
Δ


Δ


2






3






4






5






6






L






R







● : Connected status
Δ : Connected at vehicle speed above 8km/h
Tightening Torques
Item
 N.m
 Kgf.m
 lb-ft
TCM installation mounting bolt
9.8 ~ 11.8
1.0 ~ 1.2
7.2 ~ 8.7
Shift cable bracket mounting bolt
14.7 ~ 21.6
1.5 ~ 2.2
10.8 ~ 15.9
Input shaft speed sensor mounting bolt
9.8 ~ 11.8
1.0 ~ 1.2
7.2 ~ 8.7
Output shaft speed sensor mounting bolt
9.8 ~ 11.8
1.0 ~ 1.2
7.2 ~ 8.7
Shift lever assembly bolt
8.8 ~ 13.7
0.9 ~ 1.4
9.4 ~ 10.8
Inhibitor switch mounting bolt
9.8 ~ 11.8
1.0 ~ 1.2
7.2 ~ 8.7
Valve body cover mounting bolt
13.7 ~ 15.7
1.4 ~ 1.6
10.8 ~ 11.6
Eyebolt
2.9 ~ 4.9
0.3 ~ 0.5
2.2 ~ 3.6
Oil drain plug
34.3 ~ 44.1
3.5 ~ 4.5
25.3 ~ 32.6
Torque converter mounting bolt
45.1 ~ 52.0
4.6 ~ 5.3
33.3 ~ 38.3
Starter motor mounting bolt
42.2 ~ 53.9
4.3 ~ 5.5
31.1 ~ 39.8
Automatic transaxle upper mounting bolt (TM=>Eng)
42.2 ~ 53.9
4.3 ~ 5.5
31.1 ~ 39.8
Automatic transaxle lower mounting bolt (Eng=>TM)
42.2 ~ 48.1
4.3 ~ 4.9
31.1 ~ 35.4
42.2 ~ 53.9
4.3 ~ 5.5
31.1 ~ 39.8
Automatic transaxle support bracket bolt
88.3 ~ 107.9
9.0 ~ 11.0
65.1 ~ 79.6

Automatic Transaxle System
...

Lubricants
Item  Specified lubricant  Quantity Transaxle fluid ATF SP-Ⅳ or equivalent  7.3L (1.93 U.S gal.,  7.71 U.S.qt., 6.42 Imp.q ...

See also:

Relay Box (Passenger Compartment) Installation
1. Install the interior junction box. 2. Install the crash pad lower panel. 3. Check that all system operates n ...

DC/DC Converter: Circuit Diagram
   In the ISG mode, if the power of an audio system turnsOFF by drawdown while “Auto Starting” or “Idle Starting”functi ...

Rear combination lamp Installation
Rear combination lamp (Inside) [4 Door] 1. Install the rear combination lamp assembly. 2. Connect the rear combination connecto ...

Copyright © www.kirmanual.com 2014-2024