Kia Rio: Troubleshooting
| Problem Symptoms Table |
Before replacing or repairing air conditioning components, first determine
if the malfunction is due to the refrigerant charge, air flow or compressor.
Use the table below to help you find the cause of the problem. The numbers
indicate the priority of the likely cause of the problem. Check each part in
order. If necessary, replace these parts.
After correcting the malfunction, check the complete system to ensure
that performance is satisfactory.
| Symptom |
Suspect Area |
| No blower operation |
1. Blower fuse |
| 2. Blower relay |
|
| 3. Blower motor |
|
| 4. Blower resistor, Power mosfet or PWM blower module |
|
| 5. Blower speed control switch or knob |
|
| 6. Wire harness |
|
| No air temperature control |
1. Engine coolant capacity |
| 2. Heater control assembly |
|
| 3. Temperature control actuator or cable |
|
| No compressor operation |
1. Refrigerant capacity |
| 2. A/C Fuse |
|
| 3. Compressor |
|
| 4. A/C pressure transducer |
|
| 5. A/C switch |
|
| 6. Evaporator temperature sensor |
|
| 7. Wire harness |
|
| 8. High CAN |
|
| No cool comes out |
1. Refrigerant capacity |
| 2. Refrigerant pressure |
|
| 3. Drive belt |
|
| 4. Compressor |
|
| 5. A/C pressure transducer |
|
| 6. Evaporator temperature sensor |
|
| 7. A/C switch |
|
| 8. Heater control assembly |
|
| 9. Wire harness |
|
| 10. High CAN |
|
| 11. Temperature control actuator or cable |
|
| Insufficient cooling |
1. Refrigerant capacity |
| 2. Drive belt |
|
| 3. Compressor |
|
| 4. Condenser |
|
| 5. Expansion valve |
|
| 6. Evaporator |
|
| 7. Refrigerant lines |
|
| 8. A/C pressure transducer |
|
| 9. Heater control assembly |
|
| 10. High CAN |
|
| No engine idle-up when A/C switch ON |
1. Engine ECM |
| 2. Wire harness |
|
| No air inlet control |
1. Heater control assembly |
| 2. Intake actuator |
|
| No mode control |
1. Heater control assembly |
| 2. Mode control actuator or cable |
|
| No cooling fan operation |
1. Cooling fan fuse |
| 2. Fan motor |
|
| 3. Blower resistor, Power mosfet or PWM blower module |
|
| 4. Engine ECM |
|
| 5. Wire harness |
Specification
Air Conditioner
Item
Specification
Compressor
Type
DVE12 (Externally Controlled Variable Swash Plate Type)
Oil type & Capacity
PAG ...
Special Service Tools
Tool (Number and name)
Illustration
Use
09977-25100
Disc & hub assembly bolt remover
Removal and installation of disc & hub assembly ...
See also:
Adjustment
ETC module learning procedure
When installing new ETC module or re-installing it, ETC module learning
procedure must be performed.
1.
Hold the ignition key o ...
Water pump: Inspection
1.
Check each part for cracks, damage or wear, and replace the coolant
pump assembly if necessary.
2.
Check the bearing for damage, abnorma ...
A/C Pressure Transducer Replacement
1.
Disconnect the negative (-) battery terminal.
2.
Recover the refrigerant with a recovery/charging station.
3.
...
Copyright © www.kirmanual.com 2014-2024