Kia Rio Manuals

Kia Rio: Shift Lever Removal - Manual Transaxle Components - Manual Transaxle System - Kia Rio UB 2012-2026 Service ManualKia Rio: Shift Lever Removal

Shift Lever Assembly Replacement
1.
Remove the floor Interior console assembly.
(Refer to "Interior (Console)" in BD group)
2.
Remove the heater duct (A).
3.
Remove the select cable assembly after removing select cable snap pin (A) and clip (B).
4.
Remove the shift lever assembly (B) by removing the bolts (A-4ea).
Tightening torque:
8.8 ~ 13.7 N.m (0.9 ~ 1.4 kgf.m, 6.5 ~ 10.1 lb-ft)


5.
Remove the shift lever assembly (B) by removing the clip (A).

     
•
Set securely.



Select / Shift Cable Replacement
1.
Remove the floor Interior console assembly.
(Refer to "Interior (Console)" in BD group)
2.
Remove the heater duct (A).
3.
Remove the select cable assembly after removing select cable snap pin (A) and clip (B).
4.
Remove the shift lever assembly (B) by removing the bolts (A-4ea).
Tightening torque:
8.8 ~ 13.7 N.m (0.9 ~ 1.4 kgf.m, 6.5 ~ 10.1 lb-ft)


5.
Remove the clip (A) from the shift cable assembly.

     
•
Set securely.



6.
Remove the crash pad.
(Refer to "Interior (Crash pad)" in BD group.)
7.
Remove the heater unit.
(Refer to "Heater (Heater unit)" in HA group.)
8.
Remove the retainer (A) and nuts (B-2ea).
Tightening torque:
11.8 ~ 14.7 N.m (1.2 ~ 1.5 kgf.m, 8.7 ~ 10.8 lb-ft)



9.
Remove the pins (A).
10.
Remove the cable (B) from the cable bracket at manual transaxle assembly side.
11.
Remove the shift cable and select cable at cabin room.


12.
Installation is the reverse of removal.
[Shift / Select Cable Installation Tips]
1.
Installation the select and shift cable assembly (B) after removing the pin (A).
2.
Installation is the shift cable (A).

     
At this time, have to disconnect select cable.


3.
Installation is the shift lever assembly (A).
Tightening torque:
8.8 ~ 13.7 N.m (0.9 ~ 1.4 kgf.m, 6.5 ~ 10.1 lb-ft)


4.
Shift to the 3th gear position.
5.
Insert the selected cable (A) to the shift lever assembly pin (B).
6.
You have to push in the adjuster (C).
7.
Remove the neutral position pin (D).
8.
Install the snap pin (E).


Shift Lever Components
1. Shift lever knob 2. Shift lever assembly 3. Select cable assembly 4. Shift cable assembly 5. Retainer ...

Shift Lever Inspection
1. Check the select cable for proper operation and for damage. 2. Check the shift cable for proper operation and for damage. ...

See also:

Overhead Console Lamp Inspection
Remove the overhead console lamp assembly then check for continuity between terminals. If the continuity is not as specified, replace the overhead console lamp assembly. ...

Removal
1. Turn the ignition switch OFF and disconnect the battery negative (-) cable. 2. Disconnect the engine coolant temperature sensor connecto ...

Multimedia Jack Description
The multimedia jack on the console upper cover is for customers who like to listen to external portable music players like the MP3, iPod and etc., through the vehicle's sound system when ...

Categories

Copyright www.kirmanual.com 2014-2026