Kia Rio Manuals

Kia Rio: Shift Lever Removal - Automatic Transaxle Control System - Automatic Transaxle System - Kia Rio UB 2012-2026 Service ManualKia Rio: Shift Lever Removal

Shift Lever Assembly Replacement
1.
Remove the center console.
(Refer to "interior (console)" in BD group)
2.
Disconnect the connector (A)
3.
Remove the control cable (B).
4.
Remove the shift lock cable (A).
Tightening torque:
9.8 ~ 14.7 N.m (1.0 ~ 1.5 kgf.m, 7.2 ~ 10.8 lb-ft)


5.
Remove the wiring clip (A).
6.
Remove the AT lever(shift lever) assembly (B) by removing the bolts (4ea).
Tightening torque:
8.8 ~ 13.7 N.m (0.9 ~ 1.4 kgf.m, 6.5 ~ 10.1 lb-ft)


7.
Installation is the reverse of removal.

     
Adjust the shift lock cable.
(Refer to "adjustment shift lock cable" in this group)
Control Cable Assembly Replacement
1.
Remove the center console.
(Refer to "interior (console)" in BD group)
2.
Remove the control cable (A).
3.
Remove the crash pad.
(Refer to "Interior(Crash pad)" in BD group.)
4.
Remove the heater unit.
(Refer to "Heater(Heater unit)" in HA group.)
5.
Remove the retainer (A) and nuts (B).
Tightening torque:
9.8 ~ 14.7 N.m (1.0 ~ 1.5 kgf.m, 7.2 ~ 10.8 lb-ft)


6.
Remove the nut (A) from the manual control lever.
7.
Remove the control cable (B) from the bracket (C) at transaxle assembly side.
(Refer to "Automatic Transaxle" in this group)
Tightening torque:
9.8 ~ 14.7 N.m (1.0 ~ 1.5 kgf.m, 7.2 ~ 10.8 lb-ft)


8.
Remove the control cable at cabin room.
9.
Installation is the reverse of removal.

     
•
Set room side AT lever(shift lever) and automatic transaxle side manual control lever to "N" position.
•
Control cable must be free unreasonable bending.
Shift Lock Cable Replacement
1.
Remove the center console.
(Refer to "interior(console)"in BD group.
2.
Remove the shift lock cable (A).
Tightening torque:
9.8 ~ 14.7 N.m (1.0 ~ 1.5 kgf.m, 7.2 ~ 10.8 lb-ft)


3.
Remove the shift lock cable (B) from the brake pedal (A).
4.
Installation is the reverse of removal.

     
Shift lock cable must be free unreasonable bending.
Shift Lever Components
1. Shift lever knob 2. Shift lever assembly 3. Control cable 4. Shift lock cable assembly 5. Retainer 6. Brake pedal assembly ...

Shift Lever Adjustment
Adjusting the control cable 1. Set room side AT lever(shift lever) and automatic transaxle side manual control lever to "N" position. ...

See also:

Front Hub / Knuckle Inspection
1. Check the hub for cracks and the splines for wear. 2. Check the brake disc for scoring and damage. 3. C ...

Specifications
Item Specification Power source DC 14.4V (-) ground Frequency range / Channel space FM : 87.5 ~ 107.9 MHz / 200 K AM : 530 ~ 1710 KHz / 10 K ...

Adjustment
Brake Pedal Height and Free Play 1. Disconnect the stop lamp switch connector (A). 2. Adjust the brake pedal height (A) as illustrat ...

Categories

Copyright www.kirmanual.com 2014-2026