Kia Rio: Special Service Tools
| Tool (Number and Name) |
Illustration |
Use |
| 09200-38001,3N000 (Beam) 09200-1P100, 4X000 (Adapter) 09200-2S200 (Supporter) Engine support assembly |
|
Removal and installation of the transaxle. Use assembling 09200-1P100, 4X000 (Adapter) and 09200-2S200 (Supporter) on 09200-38001, 3N000(Beam). |
| 09200-3N000 Engine support fixture (Beam) |
|
Removal and installation of the transaxle. Use this adapter (SST No. : 09200-1P100, 4X000) with the supporter (SST No. : 09200-2S200). ※Permit operating with 09200-38001. |
| 09200-1P100 Engine support fixture (Adapter) |
|
Removal and installation of the transaxle. Use this beam (SST No. : 09200-38001/09200-3N000) with the supporter (SST No. : 09200-2S200) and adapter (SST No. : 09200-4X000) |
| 09200-4X000 Engine support fixture (Adapter) |
|
Removal and installation of the transaxle. Use this beam (SST No. : 09200-38001/3N000) with the supporter (SST No. : 09200-2S200) and adapter (SST No. : 09200-1P100) |
| 09200-2S200 Engine support fixture (Supporter) |
|
Removal and installation of the transaxle. Use this beam (SST No. : 09200-38001/09200-3N000) with the adapter (SST No. : 09200-1P100, 4X000) |
※ Engine support fixture special tool assembly drawing
| 1. 09200-3N000(Main bar) 2. 09200-3N000(Sub bar) 3. 09200-3N000(Handle) 4. 09200-3N000(Stopper) 5. 09200-3N000(Bolt-1) 6. 09200-4X000 (Adapter) 7. 09200-1P100(Supporter) 8. 09200-2S200(Supporter) 9. 09200-3N000(Nut) |
10. 09200-3N000(Snap ring) 11. 09200-3N000(Sub fixture) 12. 09200-3N000(Stopper) 13. 09200-3N000(Nut) 14. 09200-2S100(Spacer) 15. 09200-1P100(Sub fixture) 16. 09200-1P100(Nut) 17. 09200-3N000(Pin) |
Lubricants
Items
Recommnend lubricant
Quantity
Transaxle gear oil
SAE 75W/85
1.8 ~1.9L (0.48 ~0.50 U.S.gal., 1.90 ~ 2.0 U.S. qt., 1.58 ~
1.67 lmp qt.)
...
Inspection
Manual Transaxle Oil Inspection
1.
Park the vehicle on a level ground and stop the engine.
2.
Retighten the oil filler plug (A ...
See also:
ECM Problem Inspection Procedure
1.
TEST ECM GROUND CIRCUIT: Measure resistance between ECM and chassis
ground using the backside of ECM harness connector as ECM side check
point. If the problem is fo ...
Water pump: Inspection
1.
Check each part for cracks, damage or wear, and replace the coolant
pump assembly if necessary.
2.
Check the bearing for damage, abnorma ...
4Door Side Body
Front side member tooling hole (Ø12)
Fender apron upper member tooling hole (Ø7)
Front door upper hinge ...
Copyright © www.kirmanual.com 2014-2023