Kia Rio: Specifications
Item
|
Specification
|
Master cylinder
|
Type
|
Fixed
|
Cylinder I.D.
|
20.64 mm (0.813 in)
|
Piston stroke
|
36±1 mm (1.42±0.039 in)
|
Fluid level switch
|
Provided
|
Brake booster
|
Type
|
10" Single
|
Boosting ratio
|
7 : 1
|
Front Disc brake
|
Type
|
14" Disc
|
15" Disc
|
Ventilated disc
|
Ventilated disc
|
Disc O.D.
|
256 mm (10.08 in)
|
280 mm (11.02 in)
|
Disc thickness
|
22 mm (0.87 in)
|
22 mm (0.87 in)
|
Caliper piston
|
Single
|
Single
|
Cylinder I.D.
|
Ø 54mm (2.13 in)
|
Ø 54mm (2.13 in)
|
Rear Disc brake
|
Type
|
Solid disc
|
Disc O.D.
|
262 mm (10.31 in)
|
Disc thickness
|
10 mm (0.39 in)
|
Caliper piston
|
Single
|
Cylinder I.D.
|
Ø 34 mm(1.34 in)
|
Rear brake (Drum)
|
Type
|
Leading trailing
|
Drum I.D
|
203.2 mm (8 in)
|
Brake lining thickness
|
4.5 mm (0.18 in)
|
Clearance adjustment
|
Automatic
|
Parking brake (Disc)
|
Type
|
BIR (Ball-in-Ramp)
|
actuation
|
Lever
|
|
O.D.: Outer Diameter
I.D: Inner Diameter
|
Part
|
Item
|
Standard value
|
Remark
|
HECU
|
System
|
4 Channel 4 Sensor (Solenoid)
|
Total control
|
Type
|
Motor, valve relay integrated type
|
(ABS, EBD, TCS, ESC)
|
Operating Voltage
|
10 ~ 16 V
|
|
Operating Temperature
|
-40 ~ 120 °C (-40 ~ 248°F)
|
|
Motor power
|
270 W
|
|
Active Wheel speed sensor
|
Supply voltage
|
DC 4.5 ~ 20 V
|
|
Output current low
|
5.9 ~ 8.4 mA
|
|
Output current high
|
11.8~ 16.8 mA
|
|
Output range
|
1 ~ 2500 Hz
|
|
Tone wheel
|
48 teeth
|
|
Air gap
|
0.4 ~ 1.0 mm
|
|
Yaw rate& Lateral G sensor
(CAN TYPE)
|
Operating Voltage
|
10 ~ 16 V
|
|
Current Consumption
|
Max. 140 mA
|
|
Yaw rate sensor measurement range
|
-75 ~ +75 °/sec
|
|
Lateral G sensor measurement range
|
-14.715 ~ 14.715 m/s²
|
|
Items
|
Standard value
|
Brake pedal height
|
174.2 mm (6.86 in)
|
Brake pedal Full stroke
|
108 mm (4.25 in)
|
Stop lamp clearance
|
1.0 ~ 2.0 mm (0.04 ~ 0.08 in)
|
Front brake disc thickness
|
22 mm (0.87 in)
|
Front brake disc pad thickness
|
11 mm (0.43 in)
|
Rear brake disc thickness
|
10 mm (0.39 in)
|
Rear brake disc pad thickness
|
10 mm (0.39 in)
|
Items
|
N.m
|
kgf.m
|
lb-ft
|
Hub nut
|
88.3 ~ 107.9
|
9.0 ~ 11.0
|
65.1 ~ 79.6
|
Master cylinder to brake booster
|
12.7 ~ 16.7
|
1.3 ~ 1.7
|
9.4 ~ 12.3
|
Brake booster mounting nuts
|
16.7 ~ 25.5
|
1.7 ~ 2.6
|
12.3 ~ 18.8
|
Air bleeding screw
|
6.9 ~ 12.7
|
0.7 ~ 1.3
|
5.1 ~ 9.4
|
Brake tube flare nuts
|
12.7 ~ 16.7
|
1.3 ~ 1.7
|
9.4 ~ 12.3
|
Front caliper guide rod bolts
|
21.6 ~ 31.4
|
2.2 ~ 3.2
|
15.9 ~ 23.1
|
Rear caliper guide rod bolts
|
21.6 ~ 31.4
|
2.2 ~ 3.2
|
15.9 ~ 23.1
|
Front caliper assembly to knuckle
|
78.5 ~ 98.1
|
8.0 ~ 10.0
|
57.9 ~ 72.3
|
Rear caliper assembly to knuckle
|
49.0 ~ 58.8
|
5.0 ~ 6.0
|
36.2 ~ 43.4
|
Brake hose to caliper
|
24.5 ~ 29.4
|
2.5 ~ 3.0
|
18.1 ~ 21.7
|
Brake pedal member bracket bolts
|
9.8 ~ 14.7
|
1.0 ~ 1.5
|
7.2 ~ 10.8
|
Brake pedal shaft nut
|
24.5 ~ 34.3
|
2.5 ~ 3.5
|
18.0 ~ 25.3
|
Wheel speed sensor mounting bolt
|
7.8 ~ 11.8
|
0.8 ~ 1.2
|
5.8 ~ 8.7
|
HECU bracket mounting nut
|
16.7 ~ 25.5
|
1.7 ~ 2.6
|
12.3 ~ 18.8
|
Items
|
Recommended
|
Quantity
|
Brake fluid
|
DOT 3 or DOT 4
|
As required
|
Brake pedal bushing and bolt
|
Chassis grease
|
As required
|
Parking brake shoe and backing plate contacting surface
|
Heat resistance grease
|
As required
|
Front caliper guide rod and boot
|
MES4-3-614
|
1.2 ~ 1.7 g, 1.0 ~ 1.5 g
|
Rear caliper guide rod and boot
|
MES4-3-614 (SB 1063)
|
0.8 ~ 1.3 g
|
Tool (Number and Name)
Illustration
Use
09581-11000
Piston expander
Spreading the front disc brake piston
09580 - 0U000
Brak ...
See also:
Shift Lever Adjustment
Adjusting the control cable
1.
Set room side AT lever(shift lever) and automatic transaxle side
manual control lever to "N" position.
...
Parking Brake Adjustment
•
Re-setting of the parking brake is necessary after overhauling
the caliper body, or if ...
Adjustment
Battery charging
In general, vehicle battery charging system has three forms.
1.
Constant current charge: The battery voltage gradually rises by
chargi ...
Brake System
Special Service Tools